🚨 Upcoming ECC Training Dates Are Live! Secure Your Spot Now – Limited Places Available! 🎓

Smooth On Smooth Cast 300

$342.00$1,560.00
+ GST ($376.20 - $1,716.00 AUD)

We accept

30-days Free Returns

See policies

The Smooth-Cast™ Semi-Rigid line of low-cost semi-rigid urethane casting resins cure quickly to semi-rigid plastics that offer excellent impact resistance. These plastics are easy-to-use (mix ratio is 1A:1B by volume) and have low viscosities for minimal bubble entrapment. Vibrant colours are possible by adding SO-Strong™ colour tints or Ignite™ colour pigments.

Safety – Materials should be stored and used in a warm environment (73° F / 23° C). These products have a limited shelf life and should be used as soon as possible. All liquid urethanes are moisture sensitive and will absorb atmospheric moisture. Mixing tools and containers should be clean and made of metal, glass or plastic. Mixing should be done in a well-ventilated area. Wear safety glasses, long sleeves and rubber gloves to minimize contamination risk. Because no two applications are quite the same, a small test application to determine suitability for your project is recommended if performance of this material is in question.

Applying A Release Agent – A release agent is necessary to facilitate demolding when casting into or over most surfaces. Use a release agent made specifically for mold making (Universal® Mold Release or Ease Release® 200). A liberal coat of release agent should be applied onto all surfaces that will contact the plastic.

IMPORTANT: To ensure thorough coverage, apply release and brush with a soft brush over all surfaces. Follow with a light mist coating and let the release agent dry for 30 minutes. Smooth-On silicone rubber molds usually do not require a release agent unless casting silicone into the mold. Applying a release agent will prolong the life of the mold.


MEASURING & MIXING… Liquid urethanes are moisture sensitive and will absorb atmospheric moisture. Mixing tools and containers should be clean and made of metal, glass or plastic. Materials should be stored and used in a warm environment (73°F/23°C).

Stir or shake both Part A & Part B thoroughly before dispensing. After dispensing equal amounts of Parts A and B into mixing container (100A:90B by weight) and mix thoroughly. Stir deliberately making sure that you scrape the sides and bottom of the mixing container several times. Be careful not to splash low viscosity material out of the container.


POURING, CURING & PERFORMANCE

Pouring – Pour your mixture in a single spot at the lowest point of the containment field and let the mixture seek its level. This will help minimize air entrapment.

For Best Results . . . Best results are obtained using a pressure casting technique. After pouring the mixed compound, the entire casting assembly (mold, dam structure, etc.) is placed in a pressure chamber and subjected to 60 PSI (4.2 kg/cm2) air pressure for the full cure time of the material.

Curing – Important: Use this product with at least room size ventilation or in proximity to a forced outlet air vent and do not inhale/breath fumes. Fumes, which may be visible with a significant mass concentration, will quickly dissipate with adequate ventilation. Castings with significant mass may be hot to the touch and irritate skin immediately following cure. Let casting cool to room temperature before handling.

Demold time of the finished casting depends on mass and mold configuration. Low mass or thin-walled castings will take longer to cure than castings with higher mass concentration. Smooth-Cast® 300 will cure in 7 – 10 minutes depending on mass and mold configuration.

Post Cure – Castings will reach “full cure” faster and achieve maximum physical properties if post cured. Allow material to cure for recommended Cure Time at room temperature followed by 4 – 6 hours at 150°F/65°C. Allow casting to come to room temperature before handling.

Performance – Cured castings are rigid and durable. They resist moisture, moderate heat, solvents, dilute acids and can be machined, primed/ painted or bonded to other surfaces (any release agent must be removed). If machining cured material, wear dust mask or other apparatus to prevent inhalation of residual particles. Castings can be displayed outdoors after priming and painting. Unpainted castings will yellow over time – more quickly when exposed to ultra-violet light.

  • Free shipping over $ 120

  • Delivers in: 3-7 Working Days

Products Our Clients Can’t Get Enough Of

Explore our Catalog
bespoke seal

Bespoke Seal

$280.00
+ GST ($308.00 AUD)

Alpha X satin finish can, 1 system 3 coats

Alpha X, Satin – 1kg

$162.00
+ GST ($178.20 AUD)

Hand holding shredded material over black container.

AR Glass 12mm Fibre

$62.00$170.00
+ GST ($68.20 - $187.00 AUD)

Options This product has multiple variants. The options may be chosen on the product page
Hand holding glass fiber reinforcements.

PVA Fibre, RECS 100

$29.50$622.00
+ GST ($32.45 - $684.20 AUD)

Options This product has multiple variants. The options may be chosen on the product page
Alpha Concrete Countertop Sealer - Matte Finish

Alpha Concrete Sealer

$180.00
+ GST ($198.00 - $198.00 AUD)

Options This product has multiple variants. The options may be chosen on the product page
Hand holding polymer resin fibers

PVA Fibre, RECS 15

$29.50$622.00
+ GST ($32.45 - $684.20 AUD)

Options This product has multiple variants. The options may be chosen on the product page
Explore our Catalog

Get a Quote

Reach out for the form below and we will get back to you with details.

Product Quote